Terra Nova Roofing & Construction logoTerra Nova Roofing & Construction
Roof Flashing Guide Β· Step Flashing Β· North Jersey

Step Flashing: What It Is, How It Fails and How It's Fixed

Water stain on the wall beside a dormer, chimney or split-level? Missing or failed step flashing is one of the most common reasons. This guide from Terra Nova Roofing & Construction explains how step flashing works, how to spot a failure and what a proper repair involves, with real prices.

Licensed & insured β€’ NJ Lic. #13VH13824700 β€’ Locally owned in Garfield, NJ β€’ Free inspection with photos β€’ Hablamos espaΓ±ol

Text a photo of the wall-to-roof joint and the stain inside to 973-200-1617 and we'll tell you what we see.

  • βœ“ Same-day appointments often available
  • βœ“ Licensed & insured in NJ
  • βœ“ Homes & businesses
  • βœ“ English & EspaΓ±ol

What is step flashing on a roof?

Step flashing is a series of small, bent metal pieces woven into each row of shingles wherever a sloped roof meets a vertical wall, dormer or chimney, so water running down the wall is lapped back onto the shingles below. Terra Nova Roofing & Construction installs and repairs step flashing across North Jersey; repairs start from $650 and re-flashing a wall or chimney from $950, priced exactly after a free inspection. NJ Lic. #13VH13824700. Call or text 973-200-1617.

How does step flashing work?

Step flashing works by overlapping, like shingles do, so water always lands on top of the piece below it. Each piece is a small rectangle of metal bent into an L: one leg lies on the roof deck, the other runs up the wall.

As each row (course) of shingles goes on, a new piece of step flashing is set on top of it, tight against the wall, and the next shingle covers its roof leg. The result is a staircase of metal pieces up the side of the wall, each one lapped over the one below. Water running down the wall hits the vertical leg, drops onto the roof leg, and runs out onto the shingle beneath it.

The vertical legs are then covered by siding or, on masonry, by counter flashing, so water can't get behind them from above. It's a simple system, and when it's done right it doesn't rely on caulk at all.

Where is step flashing used on a roof?

Anywhere the side of a sloped roof runs into something vertical:

🏠

Dormer sides

Both cheeks of every dormer, a very common leak spot on capes.

🧱

Chimney sides

The two sides of a chimney that run parallel to the slope, under counter flashing cut into the brick.

🏘️

Split-levels and second stories

Where a lower roof meets the siding of the upper level.

πŸšͺ

Porch and addition roofs

Where a porch, garage or addition roof slopes along the wall of the house.

πŸͺŸ

Skylights

The sides of most skylights, usually as part of the manufacturer's flashing kit.

🏚️

Attached homes

Where a sloped roof runs along a neighbor's taller wall.

Related: sidewall flashing, dormer flashing repair and chimney flashing.

How is step flashing different from other roof flashing?

Step flashing is one part of a system. Each type has its own job:

Flashing typeWhere it goesWhat it does
Step flashingSide of a slope against a wall or chimneyIndividual pieces woven into each shingle course
Counter flashingOver the top of step flashing on masonryCovers the vertical legs so water can't get behind them
Apron (headwall) flashingWhere the top of a wall meets the bottom of a slope above, or the front of a chimneyOne continuous piece across the joint
Kickout flashingBottom end of a roof-to-wall joint, at the gutterTurns water away from the wall and into the gutter
Valley flashingWhere two roof slopes meetCarries the heavy water flow of a valley
Drip edgeEaves and rakesProtects the deck edge and directs water into the gutter

More: counter flashing, kickout flashing and roof flashing basics.

Why does step flashing fail?

Most step flashing problems are installation problems, not old age:

❌

It was never installed

A bead of caulk or a single long strip of metal where step flashing should be. It works for a while, then leaks.

πŸ”

Reused on a re-roof

Old, bent or rusted pieces left in place when the shingles were replaced.

🟀

Rust and corrosion

Thin or uncoated steel rusts through over time, especially where debris holds moisture.

πŸ“

Pieces too small

Short legs that don't reach far enough up the wall or onto the roof.

πŸͺ΅

Siding tight to the roof

Siding pushed down onto the shingles wicks water and hides the flashing.

β†˜οΈ

No kickout at the bottom

Water at the end of the joint pours behind the siding instead of into the gutter.

More: step flashing failure.

What are the signs of a step flashing leak?

A step flashing leak usually shows up on a wall or ceiling right beside where a roof meets a wall, not in the middle of a room. Look for:

  • Stains on a wall below a dormer or on the ceiling just inside an outside wall.
  • Peeling paint or soft drywall next to a chimney.
  • Rot or swelling in siding and trim where the lower end of a roof meets the wall, a classic sign of missing kickout flashing.
  • Stains on the attic sheathing or rafters along the wall line.
  • Leaks only in wind-driven rain, when water is blown sideways into the joint.
  • Thick caulk or tar along the joint on the outside, a sign someone has been chasing a leak.

Because water can travel behind siding before it shows, these leaks are often misdiagnosed. When the source isn't obvious, a thermal (infrared) roof scan (a paid service, priced up front) can help show where moisture has spread.

How should step flashing be installed?

Done right, step flashing goes in one piece per course, in this order:

1

Underlayment up the wall

Ice & water barrier or underlayment turned up the wall a few inches as a backup layer.

2

Base piece at the bottom

The lowest piece set over the starter course, with a kickout where the joint ends at a gutter.

3

One piece per shingle course

Each new piece on top of the shingle below, tight to the wall, overlapping the piece beneath.

4

Nail the roof leg only

One nail high on the roof leg, never through the vertical leg into the wall, so the joint can move without tearing.

5

Cover the vertical legs

Siding brought down over the flashing with a gap above the shingles, or counter flashing cut into the brick on chimneys.

6

No caulk as the main seal

Sealant is only for small details; the overlap does the work.

Guide: step flashing repair, step by step.

How is step flashing repaired, and what does it cost?

Fixing step flashing properly means removing the shingles along the joint, and often the bottom course of siding, so new pieces can be woven in one course at a time. Caulking the joint from the outside doesn't fix it.

A typical step flashing repair:

  1. Remove the shingles along the wall and lift or remove the lowest siding.
  2. Check the deck and the wall sheathing for rot, and replace soft wood.
  3. Install underlayment up the wall, then new step flashing course by course, with a kickout at the bottom.
  4. Re-shingle and put the siding back with a clearance gap above the roof, or install counter flashing on a chimney.
Roof leak repairFrom $650: a short section of failed flashing or a small jointStandard roof repairFrom $950: re-flashing a full dormer side, wall or chimneyEmergency leak serviceFrom $1,500: active leak with temporary dry-in firstRotted woodExtra, shown to you in photos first

You get the exact price in writing after a free inspection. More: step flashing repair, flashing repair vs. replacement and flashing repair cost.

Should step flashing be replaced when you get a new roof?

Yes. Step flashing should be replaced with every new roof, because the pieces are woven into the shingles and can't be properly reinstalled around new ones. Reusing old flashing is one of the most common causes of a leak in an otherwise brand-new roof.

On every Terra Nova roof replacement we tear off to the deck, turn ice & water barrier up the walls, and install new step flashing, counter flashing, kickout flashing, drip edge and pipe boots along with synthetic underlayment and balanced ventilation. Most homes take 1–3 days. Financing is available for larger projects, depending on the project and approval.

If the flashing failed because of storm damage, insurance may help depending on your policy and the adjuster; we document the damage but never promise a result or waive deductibles. See roof replacement, the replacement process and flashing leaks after a roof replacement.

What homeowners say about us

β˜…β˜…β˜…β˜…β˜… 5-star rated on Google

EXCELLENT
Google star 1Google star 2Google star 3Google star 4Google star 5
Based on 21 reviews
Posted on Google Google
Erick Sanchez profile picture
Erick Sanchez
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
Wonderful service, incredible work, and top-notch communication!!! Highly recommended.
Posted on Google Google
Susan Keegan profile picture
Susan Keegan
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
Terranova roofing is great. Very honest and friendly. They are knowledgeable and will tell you exactly what is needed. Reliable and on time. I highly recommend them and would definetly use them again.
Posted on Google Google
E.M G. profile picture
E.M G.
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
My roof was leaking, David gave me an estimate, I said yes right away, and they did a great job. The crew was super polite and really paid attention to the details. It couldn't have been a better experience.
Posted on Google Google
Daniel Garcia profile picture
Daniel Garcia
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
David is amazing to work with. Very responsive. His crew worked hard to get my parents roof fixed. Highly recommend. 10 ⭐️
Posted on Google Google
Davis Pinto profile picture
Davis Pinto
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
Want to thank David and his crew on working on roof. They all were very professional and taking there time on fixing the roof. No cutting corners what so ever. I highly recommend Terra Nova Roofing. Great prices. I will be using them again in the future for any leaks or damage on the roof. Once again thanks
Posted on Google Google
Jesus Flores profile picture
Jesus Flores
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
Great roofing company, replaced my roof. Highly recommend them!!!
Posted on Google Google
Joao Macavilca profile picture
Joao Macavilca
Google star 1Google star 2Google star 3Google star 4Google star 5Trustindex verifies that the original source of the review is Google.
Came by and was able to get us best pricing and did an amazing job! Highly recommended

Get a Free Flashing Inspection

Send a photo of the joint and the stain inside if you can. We'll inspect it, show you photos and give you the exact price in writing.

Why homeowners call us about flashing

  • A stain beside a dormer or chimney
  • Rotted siding where a roof meets a wall
  • Leaks only in wind-driven rain
  • Caulk along a joint that keeps failing
  • A newer roof that leaks at a wall
πŸ“ž Call 973-200-1617

Request your free estimate

Fill this out and a member of our team will follow up within one business day.

Step 1 of 2
Checkboxes

βœ“ No-obligation quote Β· βœ“ Licensed & insured Β· βœ“ Your info is never shared

Step Flashing Questions

What is step flashing?

Small L-shaped metal pieces woven into each course of shingles where a sloped roof meets a wall or chimney, overlapping so water is shed onto the shingles below.

Can step flashing be caulked instead of replaced?

Caulk can slow a leak for a while, but it isn't a repair. Proper step flashing is woven in course by course and doesn't depend on sealant.

How much does step flashing repair cost?

A small section starts from $650; re-flashing a full wall, dormer side or chimney starts from $950. Rotted wood is extra, and you get the exact price first.

How long does a step flashing repair take?

Most are done in one visit. Repairs that involve siding, rotted wood or a chimney can take longer, and we'll tell you up front.

Do I need to be home for the repair?

Not usually. If the leak shows inside, access to that room or the attic helps us confirm the fix.

What happens if it rains during the repair?

We don't leave the joint open. If rain is coming, the area is covered and sealed before we leave.

Does step flashing need to be replaced with a new roof?

Yes. We install new step flashing on every roof replacement; reusing old pieces is a common cause of leaks on new roofs.

What's the difference between step and counter flashing?

Step flashing sits under the shingles; counter flashing covers the top of the step flashing on brick or block, cut into the mortar.

Will insurance cover a step flashing leak?

Usually only if a storm caused sudden damage; installation defects and wear generally aren't covered. It depends on your policy and adjuster, and we never promise a result.

Is financing available?

Financing is available for larger projects, such as a roof replacement. Options and terms depend on the project and approval.

What does your estimate include?

Photos of the joint, what we'll remove and replace, how rotted wood is handled, the materials and the exact price.

Our service area

Bergen County

973-200-1617

Essex County

973-200-1617
  • Belleville
  • Bloomfield
  • Caldwell
  • Cedar Grove
  • East Orange
  • Essex Fells
  • Fairfield
  • Glen Ridge
  • Irvington
  • Livingston
  • Maplewood
  • Millburn
  • Montclair
  • Newark
  • North Caldwell
  • Nutley
  • Orange
  • Roseland
  • Short Hills
  • South Orange
  • Verona
  • West Caldwell
  • West Orange

Hudson County

973-200-1617
  • Bayonne
  • East Newark
  • Guttenberg
  • Harrison
  • Hoboken
  • Jersey City
  • Kearny
  • North Bergen
  • Secaucus
  • Union City
  • Weehawken
  • West New York

Union County

973-200-1617
  • Berkeley Heights
  • Clark
  • Cranford
  • Elizabeth
  • Fanwood
  • Garwood
  • Hillside
  • Kenilworth
  • Linden
  • Mountainside
  • New Providence
  • Plainfield
  • Rahway
  • Roselle
  • Roselle Park
  • Scotch Plains
  • Springfield
  • Summit
  • Union
  • Westfield

Morris County

973-200-1617
  • Boonton
  • Butler
  • Cedar Knolls
  • Chatham
  • Denville
  • Dover
  • East Hanover
  • Florham Park
  • Hanover
  • Kinnelon
  • Lincoln Park
  • Madison
  • Mendham
  • Montville
  • Morris Plains
  • Morristown
  • Mountain Lakes
  • Parsippany
  • Pequannock
  • Randolph
  • Riverdale
  • Rockaway
  • Roxbury
  • Whippany

Updated November 2026 by the Terra Nova Roofing & Construction team, Garfield, NJ β€’ NJ Lic. #13VH13824700

Scroll to Top